Adhesives
10005
10005 is an unsupported single-sided acrylic transfer tape built on a high-performance, solvent-free acrylic dispersion adhesive with a total thickness of 0.04–0.06 mm (approximately 1.6–2.4 mils). The adhesive provides balanced peel adhesion and shear performance on polar and smooth substrates, reaching 22 N/25mm peel on steel after 24 hours. The tape is rated for service from −22°F to 248°F.
Key Properties
- Peel Adhesion to Steel, 24-hour Dwell @ 73°F: 22 N/25mm
- Peel Adhesion to Glass, 24-hour Dwell @ 73°F: 20 N/25mm
- Static Shear @ 73°F, Test After 1 Hour: 500 g/2 mm
- Temperature Resistance: −22°F to 248°F
- Liner: Yellow silicone-coated paper
- Total Thickness Without Liner: 0.04–0.06 mm (~1.6–2.4 mils)
1142S-55
1142S-55 is a single-sided scrim-reinforced acrylic transfer tape consisting of a 0.5 mil acrylic (I645) adhesive layer carried on a scrim reinforcement with a 3.0 mil 55# gold glassine release liner. The scrim carrier delivers dimensional stability during handling and application while preserving the conformability of a thin acrylic transfer tape. The tape delivers 106 oz/in adhesion to steel at 72-hour dwell and a service temperature range of −4°F to 300°F.
Key Properties
- Adhesion to Steel, 72 HR Dwell: 106 oz/in (PSTC-101 — Modified, 2 mil AL Foil Backing)
- Adhesion to Steel, 15 MIN Dwell: 86 oz/in (PSTC-101 — Modified, 2 mil AL Foil Backing)
- Shear Strength (1" x 1" x 1Kg): <24 hours (PSTC-107 — Modified)
- Service Temperature: −4°F to 300°F
- Carrier / Liner: Scrim / 55# Gold Glassine Liner
- Adhesive Thickness: 0.5 mils (PSTC-133)
13010
13010 is a differential double-coated acrylic dispersion tape constructed on a transparent PET film carrier, with a high-initial-tack acrylic dispersion adhesive on the exposed side and a low-tack, nearly removable acrylic dispersion adhesive on the covered side. Total thickness without liner is 0.11–0.13 mm. The exposed side delivers 21 N/25mm peel on steel at 24-hour dwell while the covered side delivers only 0.5 N/25mm — an asymmetric design engineered for removable mounting where clean release on one face is required.
Key Properties
- Peel Adhesion to Steel, Exposed Side, 24 Hours: 21 N/25mm
- Peel Adhesion to Steel, Liner Side, 24 Hours: 0.5 N/25mm
- Static Shear @ 73°F, Test After 1 Hour: 1,000 g/2 mm
- Shear Adhesion Failure Temperature: 194°F
- Temperature Resistance: −22°F to 212°F
- Total Thickness Without Liner: 0.11–0.13 mm
254M
254M is a double-coated acrylic tape with 1.3 mil Acrylic (I630) adhesive on each side of a 0.5 mil PET film carrier, delivered on a 5.5 mil 74# poly-coated kraft liner for an 8.6 mil total thickness. The balanced high-tack, moderate-shear adhesive system provides 60 oz/in adhesion to steel at 24-hour dwell (both sides) and shear hold exceeding 7 days, with resistance to oils, plasticizers, and UV for durable service across extreme temperatures.
Key Properties
- Adhesion to Steel, 24 HR Dwell (both sides, 1 MIL PET): 60 oz/in (PSTC-101 — Modified)
- Adhesion to Steel, Initial (both sides, 4 MIL Aluminum Foil): 70 oz/in (PSTC-101 — Modified)
- Shear Adhesion: >7 days (PSTC-107 — Modified)
- Adhesive Thickness: 1.3 mils per side (PSTC-133)
- Carrier: 0.5 mil PET Film
- Total Thickness: 8.6 mils (PSTC-133)
256M
256M is a double-coated acrylic tape with 2 mils of Acrylic (I630) adhesive on each side of a 0.5 mil PET film carrier, supplied on a 5.5 mil 74# poly-coated kraft liner for a 10 mil total thickness. The high-tack, moderate-shear adhesive system delivers 70 oz/in adhesion to steel at 24-hour dwell (both sides) and shear hold exceeding 7 days, with explicitly rated Excellent plasticizer and oil resistance.
Key Properties
- Adhesion to Steel, 24 HR Dwell (both sides, 1 MIL PET): 70 oz/in (PSTC-101 — Modified)
- Adhesion to Steel, Initial (both sides, 4 MIL Aluminum Foil): 75 oz/in (PSTC-101 — Modified)
- Shear Adhesion: >7 days (PSTC-107 — Modified)
- Adhesive Thickness: 2 mils per side (PSTC-133)
- Carrier: 0.5 mil PET Film
- Total Thickness: 10 mils (PSTC-133)
654M
654M is a double-coated acrylic LSE tape with 2 mils of Acrylic (I626) adhesive on each side of a 0.5 mil PET film carrier, supplied on a 5.5 mil 74# poly-coated kraft liner for a 10 mil total thickness. Engineered for automotive interior applications on low surface energy substrates including ABS, TPO, powder-coated paints, PE, PP, and numerous foams, the tape passes SAE J-1756 automotive fogging (@ 100°C) and SAE J-1351 odor testing. Peel adhesion reaches 180 oz/in (liner side, 2 mil aluminum foil) with shear hold exceeding 7 days.
Key Properties
- Adhesion to Steel, Liner Side (2 MIL Aluminum Foil): 180 oz/in (PSTC-101 — Modified)
- Adhesion to Steel, Exposed Side (2 MIL Aluminum Foil): 165 oz/in (PSTC-101 — Modified)
- Loop Tack, Exposed Side: 120 oz/inch (PSTC-16)
- Shear Adhesion: >7 days (PSTC-107 — Modified)
- Carrier: 0.5 mil PET Film
- Total Thickness: 10 mils (PSTC-133)
7744-12
7744-12 is a single-sided acrylic transfer tape consisting of a 3.8 mil acrylic (I627) adhesive layer on an 11.3 mil 12-point poly-coated kraft liner. Formulated specifically for low surface energy (LSE) substrates and foam bonding, it delivers 106 oz/in adhesion to steel at 24-hour dwell, 118 oz/in loop tack, and >40 hours of shear adhesion at 72°F. The thick adhesive layer provides excellent edge wrap resistance in foam bonding applications, with a service temperature range of −30°F to 220°F.
Key Properties
- Adhesion to Steel, 24 HOUR Dwell (1 MIL PET): 106 oz/in (PSTC-101 — Modified)
- Loop Tack: 118 oz/in (PTSC-16)
- Shear Adhesion @ 72°F: >40 hours (PSTC-107 — Modified)
- Service Temperature: −30°F to 220°F
- Liner: 12-point poly-coated kraft (11.3 mils)
- Adhesive Thickness: 3.8 mils (PSTC-133)
A-803
A-803 is a 3.0 mil acrylic pressure sensitive adhesive transfer tape with a 5.6 mil 76# poly-coated kraft liner (8.6 mil total thickness). Formulated for general-purpose converting on paper, metal, and low-plasticized plastics, it delivers 103 oz·f/in peel adhesion (180°, 20-minute dwell) and 240+ hours of static shear hold at 1000 grams at 73°F. The service temperature range extends from −40°F to 300°F continuous (325°F intermittent), and the adhesive is compliant with JIS-A low-VOC, ISO 18902 acid-free, and ISO 18916 photographic archiving standards.
Key Properties
- Peel Adhesion, 12 IPM @ 180°, 20-Minute Dwell: 103 oz·f/in (ASTM D3330)
- Static Shear Test (1000 grams @ 73°F): 240+ hours (ASTM D3654)
- Operating Temperature — Continuous: −40°F to 300°F
- Operating Temperature — Intermittent: 325°F
- Liner: 76# poly-coated kraft (5.6 mils)
- Total Thickness: 8.6 mils (3.0 mil adhesive + 5.6 mil liner)
A462DC
A462DC is a double-coated LSE acrylic tape constructed with 2.0 mils of aggressive acrylic pressure sensitive adhesive on each side of a 0.5 mil polyester (PET) film carrier, yielding a 4.50 mil total thickness. Engineered for superior bonding to a wide range of low surface energy materials and foams including polyolefins and both ether- and ester-type polyurethanes, it delivers 75 oz/in peel adhesion and 168 hours of shear hold at 2.2 psi. A biocide additive provides enhanced microbial resistance, and the service temperature range extends from −40°F to 250°F.
Key Properties
- Peel Adhesion: 75 oz/in (PSTC-101)
- Tack: 55 oz/in (ASTM D2979)
- Shear Adhesion @ 2.2 psi: 168 hrs (PSTC 107)
- Tensile Strength: 15 lb/in (PSTC-131)
- Maximum Service Temperature: 250°F
- Total Thickness: 4.50 mils (PSTC-133)
A463
A463 is a 3.00 mil unsupported permanent acrylic pressure sensitive adhesive transfer tape delivered on a 76# moisture-stable poly-coated kraft liner. Formulated for bonding to low surface energy (LSE) substrates and foams — including polyolefins and both ether- and ester-based polyurethanes — it delivers 80 oz/in peel adhesion, 88 oz/in tack, and 168 hours of shear adhesion at 2.2 psi. The service temperature range extends from −40°F to 250°F, and the adhesive includes a biocide additive for enhanced microbial resistance.
Key Properties
- Peel Adhesion: 80 oz/in (PSTC-101)
- Tack: 88 oz/in (ASTM D2979)
- Shear Adhesion @ 2.2 psi: 168 hrs (PSTC 107)
- Maximum Service Temperature: 250°F
- Liner: 76# moisture stable poly-coated kraft
- Total Thickness: 3.00 mils (PSTC-133)
A702
A702 is a single-coated, self-wound polyester (PET) film tape constructed with a 2.00 mil PET carrier coated with 1.50 mils of acrylic adhesive, yielding a 3.50 mil total thickness. Designed for superior performance in high-temperature applications, it delivers 54 oz/in peel adhesion, 168 hours of shear hold at 2.2 psi, and 50 lb/in tensile strength. The service temperature range extends from −40°F to 300°F.
Key Properties
- Peel Adhesion: 54 oz/in (PSTC-101)
- Shear Adhesion @ 2.2 psi: 168 hrs (PSTC 107)
- Tack: 30 oz/in (ASTM D2979)
- Tensile Strength: 50 lb/in (PSTC 131)
- Maximum Service Temperature: 300°F
- Total Thickness: 3.50 mils (PSTC-133)
Acrylic Adhesive (A3)
Acrylic Adhesive (A3) is a general-purpose emulsion-based acrylic pressure sensitive adhesive, supplied at a minimum 2 mil adhesive thickness. The formulation is an aggressive permanent adhesive that bonds quickly to most surfaces, delivering a minimum 2 lb/in width adhesion to steel (1 mil PET backing) per ASTM D1000. The adhesive is rated for service from −30°F to 180°F.
Key Properties
- Adhesion to Steel (1 MIL PET): 2 lb/in width minimum (ASTM D1000)
- Adhesive Type: Acrylic (Emulsion based)
- Adhesive System: Permanent Adhesive
- Adhesive Thickness: 2 mils minimum
- Recommended Temperature Range: −30°F to 180°F
- Recommended Application Range: 50°F to 110°F
Acrylic Adhesive (EP)
APSAEP is a cloth-supported acrylic pressure sensitive adhesive construction with silicone adhesive (2.9–3.1 mils) on one face and acrylic adhesive (1.9–2.1 mils) on the opposite face, built on a 3.0 mil cloth carrier. The acrylic side delivers 80+ oz/in peel to stainless steel (180°, 3-day dwell), 100+ oz/in to acrylic and glass (90° angle), and a service temperature range of −40°F to 302°F. The semi-bleached kraft release liner is 4.7 mils with an additional 2 mil polyester liner layer.
Key Properties
- Adhesion to Stainless Steel, Acrylic Side, 3 Days RT, 180°: 80+ oz/in (ASTM D3330, laminated to 2 mil polyester)
- Adhesion to Glass, Acrylic Side, 3 Days RT, 90°: 100+ oz/in (ASTM D3330, laminated to 2 mil aluminum foil)
- Adhesion to Polypropylene, Acrylic Side, 3 Days RT, 180°: 26 oz/in (ASTM D3330)
- Tack, Acrylic Adhesive (2 MIL Clear Polyester): 840 gm (ASTM D2979)
- Service Temperature Range, Acrylic Side: −40°F to 302°F
- Adhesive Thickness: 2.9–3.1 mils silicone / 1.9–2.1 mils acrylic / 3.0 mil cloth carrier
Acrylic Adhesive (S3)
Acrylic Adhesive (S3) is a solvent-based acrylic pressure sensitive adhesive formulated for specialty applications requiring good weathering and creep resistance, supplied at a minimum 2 mil thickness. The adhesive delivers a minimum 1.5 lb/in width adhesion to steel (1 mil PET backing) per ASTM D1000, with a recommended temperature range of −40°F to 180°F — extending 10°F lower than the emulsion-based APSAA3 grade.
Key Properties
- Adhesion to Steel (1 MIL PET): 1.5 lb/in width minimum (ASTM D1000)
- Adhesive Type: Acrylic (Solvent based)
- Adhesive System: Permanent Adhesive
- Adhesive Thickness: 2 mils minimum
- Recommended Temperature Range: −40°F to 180°F
- Recommended Application Range: 50°F to 110°F
Acrylic Netbond 10
Acrylic Netbond 10 is a scrim-reinforced single-sided acrylic transfer adhesive built on a polyester scrim carrier with a high-tack solvent-free acrylic dispersion adhesive. Total thickness without liner is 0.04–0.06 mm. Peel adhesion builds to 24 N/25mm on steel after 24 hours and 20 N/25mm on glass, with a shear adhesion failure temperature (SAFT) of 270°F — the highest in the Netbond series. Temperature resistance extends from −22°F to 248°F, with High ratings for aging, condensation water, and plasticizer resistance.
Key Properties
- Peel Adhesion to Steel, 24-Hour Dwell: 24 N/25mm
- Peel Adhesion to Glass, 24-Hour Dwell: 20 N/25mm
- Shear Adhesion Failure Temperature: 270°F
- Static Shear @ 73°F, 1 Hour: 1,000 g/5 mm
- Temperature Resistance: −22°F to 248°F
- Total Thickness Without Liner: 0.04–0.06 mm
Acrylic PSA (DP)
APSADP is a non-woven nylon supported acrylic/silicone differential laminating adhesive with acrylic adhesive (2 mils) on one face and silicone adhesive (2.5 mils) on the opposite face, carried on 4oz non-woven nylon. The acrylic side delivers 150–170 lb/in peel at 24-hour applied dwell (the highest peel value in the APSA family), and the silicone side delivers 60–80 lb/in peel across both immediate and 24-hour applied dwell. Continuous service temperature spans −65°F to 250°F with short-term capability to 350°F.
Key Properties
- Peel Adhesion, Acrylic Side, 24 Hour Applied: 150–170 lb/in (PSTC-101)
- Peel Adhesion, Silicone Side, 24 Hour Applied: 60–80 lb/in (PSTC-101)
- Shear Adhesion, Both Sides (1" × 1", 1,000 g @ 72°F): 24+ (PSTC-107)
- Continuous Service Temperature, No Load: −65°F to 250°F
- Short-Term Service Temperature, No Load: −65°F to 350°F
- Adhesive Thickness: 2 mils acrylic / 2.5 mils silicone / 4oz non-woven nylon carrier
Acrylic PSA (FS)
Acrylic PSA (FS) is a water-based acrylic pressure sensitive adhesive with good initial tack, high shear, and excellent resistance to plasticizers common in PVC foam and other substrates. It delivers 60 oz/in width peel adhesion to stainless steel at 24-hour dwell (foam failure), 45 oz/in at 20-minute dwell, and 35 oz/in loop tack on stainless steel. Shear performance reaches 7 hours on stainless steel at 1-minute dwell under a 1,000-gram load with cohesive failure.
Key Properties
- Peel Adhesion to Stainless Steel, 24-Hour Dwell: 60 oz/in width (foam failure, ASTM D1000)
- Peel Adhesion to Stainless Steel, 20-Minute Dwell: 45 oz/in width (ASTM D1000)
- Peel Adhesion to Polypropylene, 20-Minute Dwell: 25 oz/in width (ASTM D1000)
- Loop Tack, Stainless Steel: 35 oz/in (adhesive failure, ASTM D6195)
- Static Shear, Stainless Steel (1" × 1" × 1,000g): 7 hours (cohesive failure, PSTC-7)
- Adhesive Type: Acrylic (Water based)
NB1B Acrylic Adhesive
NB1B Acrylic Adhesive is a scrim-reinforced single-sided acrylic transfer tape built on a polyester scrim carrier with a solvent-free acrylic dispersion adhesive, delivered on a white film liner. Total thickness without liner is 0.09–0.11 mm. Peel adhesion reaches 18 N/25mm on steel across all tested dwell times, with a shear adhesion failure temperature of 176°F and a temperature resistance range of −22°F to 248°F.
Key Properties
- Peel Adhesion to Steel, 24-Hour Dwell: 18 N/25mm
- Peel Adhesion to Glass, 24-Hour Dwell: 17 N/25mm
- Shear Adhesion Failure Temperature: 176°F
- Static Shear @ 73°F, 1 Hour: 500 g/5 mm
- Temperature Resistance: −22°F to 248°F
- Total Thickness Without Liner: 0.09–0.11 mm
NB1C Acrylic Adhesive
NB1C Acrylic Adhesive is a scrim-reinforced single-sided acrylic transfer tape built on a polyester scrim carrier with a solvent-free acrylic dispersion adhesive, delivered on a white paper liner. Total thickness without liner is 0.07–0.09 mm. Peel adhesion reaches 24 N/25mm on steel at 24-hour dwell and 23 N/25mm on glass — the highest peel values in the Netbond series. Shear adhesion failure temperature is 248°F with a temperature resistance range of −22°F to 248°F.
Key Properties
- Peel Adhesion to Steel, 24-Hour Dwell: 24 N/25mm
- Peel Adhesion to Glass, 24-Hour Dwell: 23 N/25mm
- Shear Adhesion Failure Temperature (SAFT @ 1.8°F/min): 248°F
- Static Shear @ 73°F, 1 Hour: 500 g/2 mm
- Temperature Resistance: −22°F to 248°F
5000M
5000M is a differential double-coated rubber adhesive tape with 1.4 mils of high-tack rubber adhesive on the exposed side and 1.3 mils of general-purpose rubber adhesive on the liner side, built on a 0.5 mil PET film carrier. The total tape thickness is 7.7 mils including the 4.5 mil 80# poly-coated kraft liner. Peel adhesion reaches 230 oz/in on the exposed side and 220 oz/in on the liner side when tested with 2 mil aluminum foil backing, with shear hold exceeding 24 hours and a service temperature range of 30°F to 150°F.
Key Properties
- Adhesion to Steel, Exposed Side (2 MIL Aluminum Foil): 230 oz/in (PSTC-101 — Modified)
- Adhesion to Steel, Liner Side (2 MIL Aluminum Foil): 220 oz/in (PSTC-101 — Modified)
- Adhesion to Steel, Exposed Side (1 MIL PET): 145 oz/in (PSTC-101 — Modified)
- Shear Adhesion: >24 hours (PSTC-107 — Modified)
- Service Temperature: 30°F to 150°F
- Total Thickness: 7.7 mils (PSTC-133)
M1207
M1207 is a double-coated rubber-based adhesive tape constructed with an aggressive permanent adhesive on both faces: 1.6 mils on the exposed side and 1.4 mils on the liner side, supported by a 0.5 mil PET film carrier. Peel adhesion reaches 115 ozf/in on stainless steel (liner side) and 100 ozf/in on ABS, with Polyken probe tack values of 1,875 g (liner side) and 1,450 g (exposed side), and shear hold exceeding 10,000 minutes on both faces. The tape passes FMVSS-302, UL723 25/50 smoke/spread, and 21 CFR 175.105 indirect food contact requirements.
Key Properties
- Peel Adhesion, Stainless Steel, Liner Side, 20 Minute Dwell: 115 ozf/in (PSTC-101, ASTM D3330)
- Peel Adhesion, ABS, Liner Side, 20 Minute Dwell: 100 ozf/in (PSTC-101, ASTM D3330)
- Polyken Probe Tack, Liner Side: 1,875 g (ASTM D2979)
- Shear Adhesion (Both Sides): >10,000 minutes (ASTM D3654, PSTC-107)
- Elevated Temperature Test: 180°F exposed / 185°F liner side (ASTM D4498 — Modified)
- Adhesive Thickness: 1.6 mils exposed / 1.4 mils liner / 0.5 mil PET carrier
R-242
R-242 is a self-wound double-coated rubber adhesive tape with 2.5 mils of aggressive permanent rubber adhesive on the exposed (air) side and 2.0 mils on the liner side, supported by a 0.5 mil PET film carrier on a 76# poly-coated kraft liner. Total thickness without liner is 5.0 mils. Peel adhesion reaches 200 oz·f/in on the air side and 157 oz·f/in on the liner side at 20-minute dwell, with static shear hold exceeding 500 hours at 1,000 grams on both faces. Continuous service temperature is 0°F to 120°F with intermittent capability to 150°F.
Key Properties
- Peel Adhesion, Air Side Adhesive, 12 IPM @ 180° 20 min dwell: 200 oz·f/in (ASTM-D3330)
- Peel Adhesion, Liner Side Adhesive, 12 IPM @ 180° 20 min dwell: 157 oz·f/in (ASTM-D3330)
- Static Shear, Both Sides (1000 g @ 73°F): 500+ hours (ASTM-D3654)
- Operating Temperature, Intermittent: 150°F
- Adhesive Thickness: 2.5 mils exposed / 2.0 mils liner / 0.5 mil PET carrier
- Total Thickness Without Liner: 5.0 mils
SLM 360
SLM 360 is a double-coated polyester (PET) film tape coated on both sides with an extremely aggressive rubber pressure sensitive adhesive at 1.5 mil adhesive thickness. Formulated for difficult bonding applications with excellent quick-stick and shear properties, it delivers 96 oz/in peel adhesion per PSTC-101 and carries three automotive OEM qualifications: GM3622, Chrysler MS-CC211, and Delphi SD2-324. Service temperature extends from −10°F to 180°F continuous.
Key Properties
- Peel Adhesion: 96 oz/in (PSTC-101)
- Adhesive Thickness: 1.5 mils
- Maximum Continuous Use Temperature: 180°F
- Minimum Continuous Use Temperature: −10°F
- Adhesive Type: Rubber
- Liner: 60# densified kraft
M1775
M1775 is a differential double-coated pressure sensitive adhesive tape combining a high-performance 1.8 mil rubber laminating adhesive on the exposed side with a 0.5 mil removable acrylic adhesive on the liner side, built on a PET film carrier for a total caliper of 2.8 mils (without liner). The exposed rubber side delivers 144 ozf/in peel adhesion on stainless steel, while the liner-side acrylic is tuned for clean removal at just 10–25 ozf/in — leaving no ghosting or residue on typical surfaces under normal environmental conditions.
Key Properties
- Peel Adhesion, SS - Exposed Side, 20 Minute Dwell: 144 ozf/in (PSTC-101, ASTM D3330)
- Peel Adhesion, SS - Liner Side, 20 Minute Dwell: 10–25 ozf/in (PSTC-101, ASTM D3330)
- Adhesive Thickness, Exposed Side: 1.8 mils (PSTC-133, ASTM D3652)
- Adhesive Thickness, Liner Side: 0.5 mils (PSTC-133, ASTM D3652)
- Total Caliper (Without Liner): 2.8 mils (ASTM D3652)
- Application Temperature Range: 50°F to 100°F
R1776 Permanent / Removable Differential Double Coated Polyester (PET) Film Tape
R1776 is a differential double coated polyester (PET) film tape with a permanent rubber pressure sensitive adhesive on the exposed side and a removable acrylic pressure sensitive adhesive on the liner side, at a total thickness of 4 mils (0.102 mm). The exposed side delivers aggressive permanent adhesion of 120 oz/in to foams, metals, plastics, and low surface energy materials across a service range of -20°F to 160°F (-29°C to 71°C). The liner side acrylic adhesive allows repositionability and clean, residue-free removal, supplied on a 76# moisture stable polycoated kraft liner.
2378SL
2378SL is a differential double-coated adhesive construction featuring a 3.0–3.1 mil silicone PSA on one face and a 1.9–2.1 mil acrylic PSA on the opposite face, supported by a 0.5 mil polyester (PET) film carrier. The construction uses a 2 mil polyester film liner on the silicone side and a 4.7 mil clay-coated semi-bleached paper liner on the acrylic side. Adhesion is asymmetric by design: the silicone side delivers up to 74 oz/in peel and the acrylic side delivers up to 244 oz/in peel (stainless steel, 3-day RT, 180°, 2 mil aluminum foil laminate). Service temperature spans −40°F to 302°F, and both adhesives are suitable for outdoor use.
Key Properties
- Peel Adhesion, Acrylic Side, SS, 3 Days @ 160°F, 180°, 2 MIL Polyester: 219 oz/in (ASTM D3330)
- Peel Adhesion, Acrylic Side, SS, 3 Days RT, 180°, 2 MIL Aluminum Foil: 244 oz/in (ASTM D3330)
- Peel Adhesion, Silicone Side, SS, 3 Days RT, 180°, 2 MIL Aluminum Foil: 74 oz/in (ASTM D3330)
- Tack, Acrylic Adhesive (2 MIL Aluminum Foil): 1,120 gm (ASTM D2979)
- Service Temperature: −40°F to 302°F
- Adhesive Thickness: 3.0–3.1 mils silicone / 1.9–2.1 mils acrylic / 0.5 mil PET carrier
Polysil™ 1003
Polysil™ 1003 is a 3.00 mil clear silicone transfer tape engineered for high-performance applications requiring chemical resistance, excellent bond strength, and resistance to extreme temperatures. The adhesive is protected by two clear fluorosilicone-coated polyester (PET) film liners. Service temperature spans −100°F to 500°F — the widest thermal range in the H-O catalog. The adhesive carries ISO 10993-10 (Primary Skin Irritation, Pass score 0) and ISO 10993-5 (Cytotoxicity, Pass score 0) biocompatibility credentials.
Key Properties
- Peel Adhesion: 64 oz/in (PSTC-101)
- Tack: 40 oz (ASTM D 2979)
- Shear Adhesion @ 2.2 psi: 168 hours (PSTC-107)
- Minimum Service Temperature: −100°F
- Maximum Service Temperature: 500°F
- Adhesive Thickness: 3.00 mils (PSTC-133)
Polysil™ SA 1911
Polysil™ SA 1911 is a differential double-coated adhesive tape engineered for bonding dissimilar materials, with 2.8 mils of silicone PSA on one face and 2.2 mils of acrylic PSA on the other, separated by a 0.5 mil PET carrier for a total thickness of 5.5 mils. The silicone face delivers 72 oz/in peel adhesion and is specifically formulated for strong bonding to silicone foams, rubber, and other low surface energy substrates. The acrylic face delivers 70 oz/in peel adhesion with excellent heated shear performance, spanning a service temperature range of −40°F to 300°F.
Key Properties
- Peel Adhesion, Silicone Side: 72 oz/in (PSTC-101)
- Peel Adhesion, Acrylic Side: 70 oz/in (PSTC-101)
- Shear Adhesion @ 2.2 PSI, Both Sides: >168 hours (PSTC-107)
- Maximum Service Temperature: 300°F
- Tensile Strength: 15 lb/in (PSTC-131)
- Total Thickness: 5.5 mils (PSTC-133)
Cling Foam (GP)
Cling Foam is a 1/16" industrial PVC foam cast to a high-gloss paper backing, producing a foam surface that adheres to non-porous substrates yet remains removable and repositionable without residue. Adhesion to both stainless steel and cork is rated 12 oz/in minimum, and the foam remains pliable from −20°C to 78°C (−4°F to 172°F). The foam is available with adhesive backing for permanent lamination to cork or other secondary substrates, supporting use as a transportation cushion or non-porous-material storage interface.
Key Properties
- Adhesion to Stainless Steel: 12 oz/in minimum
- Adhesion to Cork: 12 oz/in minimum
- Compression Deflection: 5 psi (ASTM D1667)
- Durometer / Hardness (Shore 00): 45 (ASTM D2240)
- Tensile Strength: 20 psi (ASTM D412 Die A)
- Thickness: 1/16"
